- Bally Slot Machine Parts
- Remove Bally Slot Machine Bill Changer Tool
- Value Of Bally Slot Machine
- Remove Bally Slot Machine Bill Changer Machine
- Remove Bally Slot Machine Bill Changer Parts
New Life Games ™ NewLifeGames ™ NLG ™ We Bring new Life to old Games ™ 1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2020
IGT Slot Machines; Bally Slot Machines; Williams Slot Machines; Specials; Claw and Crane Machines; Repair and Technical Information. Install or remove FutureLogic Gen2 Printer; IGT IGAME AND GAME KING. How do you set the time on an IGT IGAME Video machine? IGT IGame Key 22 Install Instructions; Converting a Game King from 13' CRT.
Bally Slot Machine Parts
FAIR USE NOTICE:This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.
For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.
Remove Bally Slot Machine Bill Changer Tool
If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.
NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.
| Powered by SMF 1.1.20 |SMF © 2013, Simple Machines Loon Designed by Mystica Updated by Runic Warrior |
Hoppers run on AC power yet the MPU that tells it to cash out runs on DC voltage. In order to do this a small interface called an SSR (Solid State Relay) is placed in between the MPU and the hopper. An SSR is a device in which DC voltage can control AC voltage.
The SSR will rarely go bad but if you have to check the power going to the hopper. This is where to check.
Once the cash out Button has been pressed the MPU send a signal through the SSR to the Hopper to begin cashing out. The coin out-optics or switch on the Hopper report back to the MPU, telling it how many coins has been paid out. Once the correct amount of credits has been given, the MPU shuts down the Hopper.
To test the hopper for the PE-Plus press the white self-test button to the test hopper page. Turn the reset-key to activate the hopper payout. This test page will pay out ten coins and is useful to see if the hopper is operating properly.
To run this test with the S-Plus push the white self-test switch until you see a “ 3 “ in the Coins Played Window then hit the spin button.
There is also an option located on the output page that will allow the hopper to run constantly until you stop it. To do this for the PE-Plus simply go to the output page use the deal-draw button until the arrow points to “HOPPER ONE” or “HOPPER TWO” ether one will work. When you turn the reset key, the hopper will run until you let go of the key.
For the S-Plus go to output page “ 2 “ then the turn the reset key to “ 35 “ once the spin button is pushed it will run until you let go.
The number one thing to go wrong by far is coin jams especially if you have a bar-top or slant-top game. Slant-tops and bar-tops have what is called the escalator that the coins have to slide up in order to get to the coin out tray. Any bent or foreign coin will jam up and cause general mayhem. If you are lucky, enough to have an upright game (because there easier to fix) then the bad coins will most often cause the coins to go under the knife.
The coin-out optic is located at the point where the coins exit the hopper. The coin-out optic tells the MPU how many coins have left the machine. If they go bad, they will generally cause a coin-out tilt. Most often, the wires leading to them are cut or mangled and no signal gets back to the MPU. Sometimes they get dirty and just need cleaning by blowing on them. (If the optics ground wire is not properly grounded it will cause a hopper runaway)
To remove the hopper simply open the door “or doors” remove the coin-in assembly and pull it out. If you have an upright game, you will not have to pull out the coin-in assembly since they are built into the door.
The hopper is connected to what is called the MOLEX connecter. All the wires from the coin-out optics and ac power for the hopper motor run through this.
The main components of a hopper depend on your game cabinet and game version. The most common are:
• Knife: This is what the coins slide up on to exit the hopper.
• Shelf and Shelf Wheel: These are to plates one smaller than the other that the coins ride up on out of the bowl and to the knife.
• Agitator: This is a star shaped thing usually made out of rubber or hard plastic that sits on the shelf in the middle of the bowl and stirs up the coins so they ride out.
Value Of Bally Slot Machine
• Escalator: This is for bar-top and slant-top models so when the coins exit the hopper they ride up the escalator and exit into the tray.
• Coin-Out Optics: Senses when a coin has or has not exited the hopper and informs the MPU.
Working on hoppers is not a fine science the only electric components are the coin-in optics and the electric motor. The electric motor can be hooked up to a wall socket to see if it works. Warning this is not suggested to be done because of obvious hazards and a proper test cord should be used when testing the motor.
Remove Bally Slot Machine Bill Changer Machine
If the coin-out optic is having a problem the hopper will still work in test mode and will spit out coins. Everything else on a hopper is mechanical and was learned after years of having to fix them. Often slot techs carry their own home made tools and have deferent methods of repairing them.
Remove Bally Slot Machine Bill Changer Parts
Before ticket in ticket out I used to carry around five pounds of tools and parts to fix them, while other slot techs would just carry a screw driver to fix a hopper. Basically if you have mechanical experience working on things like cars or truck's you will most likely not have many problems. If you do not have mechanical experience then remember how things come apart so you can put it back together again. Write it down or take pictures if you have to.
Sites to check out
http://myhomereviewsblog.com/backtrack-compatible-wireless-adapters-review
Sites to check out
http://myhomereviewsblog.com/backtrack-compatible-wireless-adapters-review
Comments are closed.